Updating a Showcase1271
Pages:
1
 WGAN BasicMember Denver |
pixelray private msg quote post Address this user | |
| Hey guys, quick question...I recently went back and rescanned some areas of a home due to lighting issues. Once that was done, I hit the upload button. I now have two showcases in Workshop. Did I do this correctly? Do I get charged for two uploads? I just wanted to disable some old scans and replace with the new ones. | ||
| Post 1 • IP flag post | ||
|
Jamie private msg quote post Address this user | |
| No its just the 1 charge assuming they are under 100 scans (well if the first was under 100 and you added more than 100, it would be an additional charge) When you reupload it makes a new model |
||
| Post 2 • IP flag post | ||
|
WGAN Basic Member Denver |
pixelray private msg quote post Address this user | |
| Thanks Jamie. It's actually the first time I have ever gone back and re-did some scans. So, I was a little freaked out when I noticed two of the same showcases in my account. I thought it would just add the new scans to the original upload. Wonder why it makes a whole new one? Oh well...as long as I don't get dinged for it. | ||
| Post 3 • IP flag post | ||
|
|
Jamie private msg quote post Address this user | |
| I guess it's just so you can keep an original. Sometimes you might want to delete parts | ||
| Post 4 • IP flag post | ||
|
danmorell private msg quote post Address this user | |
| Hi @Jamie, I recently had a similar issue with going back and getting more scans. When I reuplaoded the model with the new scans the new scans didn't connect to the previous scans in the new showcase? If I clicked into the showcase from the follow up outside scans I could click through into the inside scans but couldn't turn around back to the outside scans. The showcase wasn't showing the scan points. If I clicked into the showcase from the inside scans it didn't recognize the outside scans at all and in turn couldn't go outside despite the follow up scan points on the same model, just reuploaded. On the reupload, it did create another model like mentioned above which I'm not as worried about. Hope that makes a sense. Thank you for any feedback you might have! |
||
| Post 5 • IP flag post | ||
|
WGAN Basic Member Denver |
pixelray private msg quote post Address this user | |
| I think I may know your issue. I had something similar. If you are talking about dealing with outside scans - I have run into an issue where I would take scans of a patio and then when I tried to go back and see if everything turned out ok, I couldn't connect my outside scans with the inside - I couldn't walk to the outside patio from the inside - the scans were there, I just couldn't' walk to them - I can't remember if the scans showed up or not - but I knew they were there. I realized it wasn't allowing me to connect and walk to those outside scans because I marked the part I was trying to walk through a "window" in the capture app because it was a patio glass door. So, I had to go back and delete the "window" marking and then I could access the scans on the outside. It just wouldn't allow me to connect to those outside scans until I deleted the "window" marking. Not sure if that's what you are talking about or not - but make sure there isn't something impeding you getting to those outside scans - like a "window" marking in the capture app. |
||
| Post 6 • IP flag post | ||
|
|
danmorell private msg quote post Address this user | |
| You the man @pixelray! That's exactly it. I marked the part I was trying to walk through as a "window" as it was closed on the first session. Once the lighting changed I went out the next day and captured it and didn't think the window would cause an issue. Thank you so much for the reply! |
||
| Post 7 • IP flag post | ||
|
WGAN Basic Member Denver |
pixelray private msg quote post Address this user | |
| You bet. I drive myself crazy one day with this trying to figure out. Glad I could help | ||
| Post 8 • IP flag post | ||
Pages:
1This topic is archived. Start new topic?